TILE-CERAMIC-BASED ADHESIVES ALFIX WHITE
3.75
/Backage/Qty in backage:25 kg
متوفر
Cement-based tile-ceramic adhesive mortar with reduced slip featurer and long working time
Color:White
CONSUMPTION:3-5kg/m²
It complies with TS EN 12004 I C1TE class.
C: Cement based
1: Normal hardening (Standard performance)
T: Reduced slippage
E: Extended working time
Public Works Item No: 04.013/1
Area of Use:
It is used to apply coating materials such as tiles and ceramics horizontally and vertically, in wet areas such as bathrooms and kitchens, on surfaces such as concrete, plaster, and screed. Before applying ceramic adhesives on existing ceramics, the surface should be notched or primed with Primerfix 101, Smooth Surface Primer.
Features:
It has high adhesion power.
It is suitable for ceramic flooring from top to bottom. It does not slip.
It saves time and labor with its long working time.
It can be easily combed.
Technical Specifications:
Appearance: White Color Powder
Application Temperature: +5ºC to +35ºC
Water Mixing Ratio: 6.5-8.0 Liters/Bag
Resting Time of the Mortar: 5-10 min.
Pot Life: 1-2 hours
Slip: ≤ 0.5 mm
Open Hold Time: ~30 min.
Time to Use: On wall: 8 hrs. On floor: 24 hrs.
Adhesion Strength: ≥ 0.5 N/mm²
Fire Response: A1
Temperature Resistance: -25ºC to +80ºC
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
Care must be taken to ensure that the application surface is cured and solid. The application surface must be cleared of substances that prevent adhesion such as dust, oil and paint. Sub-surfaces that are not strong enough to support the application, such as cracked plasters and weak surfaces, should be cleaned from the application surface. Floors requiring repair should be repaired with special repair mortars at least 3-4 days before applying the adhesive. The application surface should be wetted and care should be taken to keep it moist. If the surface is very absorbent, it is recommended to use a primer on the surface.
APPLICATION:
25 kg of Alfix White Tile-Ceramic Adhesive Mortar is poured into a container filled with approximately 6.5-8.0 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained. No additives not specified in the application instructions should be added during the mixing process. The prepared mortar should be left to mature for 5-10 minutes and then mixed for 1-2 minutes until it becomes homogeneous. The mixture in the container should be consumed within 1-2 hours. The prepared mortar is spread on the surface with a notched trowel with appropriate tooth size. Coating materials such as tiles and ceramics should be adhered to the combed mortar within 20-30 minutes (This period may vary depending on the environmental conditions of the application). Pasting should not be done on expired mortar, the mortar should be scraped off the surface and new mortar should be applied again. Using a rubber hammer, the coating materials are rammed to ensure proper placement and adhesion. In outdoor applications, it can be mixed with Allmax Latex to provide stronger adhesion . Grouting should be done after 8 hours on the wall and after 1 day on the floor.
Warnings:
Avoid application at temperatures below +5ºC and above +35ºC. Newly completed applications should be protected against adverse weather conditions such as direct sunlight, excessive air currents, high air temperatures (above +35ºC), rain and frost during the first days. Avoid direct contact of the completed application with water within the first 24 hours. Never add powder or water to expired or crusted mortar in the container, throw it away. Wash all tools and application equipment with clean water immediately after use.
Consumption: 3-5 kg/m²
Consumption amounts are theoretically calculated values in a laboratory environment; we recommend that a consumption control sample be applied before application.
C: Cement based
1: Normal hardening (Standard performance)
T: Reduced slippage
E: Extended working time
Public Works Item No: 04.013/1
Area of Use:
It is used to apply coating materials such as tiles and ceramics horizontally and vertically, in wet areas such as bathrooms and kitchens, on surfaces such as concrete, plaster, and screed. Before applying ceramic adhesives on existing ceramics, the surface should be notched or primed with Primerfix 101, Smooth Surface Primer.
Features:
It has high adhesion power.
It is suitable for ceramic flooring from top to bottom. It does not slip.
It saves time and labor with its long working time.
It can be easily combed.
Technical Specifications:
Appearance: White Color Powder
Application Temperature: +5ºC to +35ºC
Water Mixing Ratio: 6.5-8.0 Liters/Bag
Resting Time of the Mortar: 5-10 min.
Pot Life: 1-2 hours
Slip: ≤ 0.5 mm
Open Hold Time: ~30 min.
Time to Use: On wall: 8 hrs. On floor: 24 hrs.
Adhesion Strength: ≥ 0.5 N/mm²
Fire Response: A1
Temperature Resistance: -25ºC to +80ºC
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
Care must be taken to ensure that the application surface is cured and solid. The application surface must be cleared of substances that prevent adhesion such as dust, oil and paint. Sub-surfaces that are not strong enough to support the application, such as cracked plasters and weak surfaces, should be cleaned from the application surface. Floors requiring repair should be repaired with special repair mortars at least 3-4 days before applying the adhesive. The application surface should be wetted and care should be taken to keep it moist. If the surface is very absorbent, it is recommended to use a primer on the surface.
APPLICATION:
25 kg of Alfix White Tile-Ceramic Adhesive Mortar is poured into a container filled with approximately 6.5-8.0 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained. No additives not specified in the application instructions should be added during the mixing process. The prepared mortar should be left to mature for 5-10 minutes and then mixed for 1-2 minutes until it becomes homogeneous. The mixture in the container should be consumed within 1-2 hours. The prepared mortar is spread on the surface with a notched trowel with appropriate tooth size. Coating materials such as tiles and ceramics should be adhered to the combed mortar within 20-30 minutes (This period may vary depending on the environmental conditions of the application). Pasting should not be done on expired mortar, the mortar should be scraped off the surface and new mortar should be applied again. Using a rubber hammer, the coating materials are rammed to ensure proper placement and adhesion. In outdoor applications, it can be mixed with Allmax Latex to provide stronger adhesion . Grouting should be done after 8 hours on the wall and after 1 day on the floor.
Warnings:
Avoid application at temperatures below +5ºC and above +35ºC. Newly completed applications should be protected against adverse weather conditions such as direct sunlight, excessive air currents, high air temperatures (above +35ºC), rain and frost during the first days. Avoid direct contact of the completed application with water within the first 24 hours. Never add powder or water to expired or crusted mortar in the container, throw it away. Wash all tools and application equipment with clean water immediately after use.
Consumption: 3-5 kg/m²
Consumption amounts are theoretically calculated values in a laboratory environment; we recommend that a consumption control sample be applied before application.
