CHEMICAL CURE MATERIALS ALLMAX THIN
2.1875
/Backage/Qty in backage:25 kg
متوفر
Used as a fine finishing plaster on rough and ready cement based plaster applications indoors and outdoors.
Color:Gray
CONSUMPTION:~1,7 kg/m²/mm
(For 1 mm thickness)
TS EN 998-1
Public Works Item No: 04.476/C
Area of Use:
Indoors and outdoors,
On the wall and ceiling,
On exposed concrete surfaces,
It is used on rough plaster and ready-mixed cement based plaster applications.
Features:
It is applied manually.
It is resistant to water, frost and humidity.
It breathes and balances the humidity level by allowing evaporation.
It has a plastic consistency and is easy to apply.
Provides a smooth surface for final coating.
Technical Specifications:
Appearance: Gray Color Powder
Dry Unit Weight: 1400 ± 300 kg/m³
Application Temperature: +5ºC to +35ºC
Water Mixing Ratio: 5.0-6.0 Liters/Bag
Applicable Thickness: 3-10 mm
Drying Time: 24 hours
Compressive Strength: ≥ 6 N/mm²
Bond Strength: ≥ 0.2 N/mm²
Capillary Water Absorption: W0
Water Vapor Permeability Coefficient: µ ≤ 25
Average Thermal Conductivity (W/mK): ≤ 0.93
Fire Response: A1
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
The surface must be cleared of mold oil, dust, paint and adhesion reducing substances.
Before application, cracks and holes should be repaired with appropriate repair mortars.
If necessary, the application surface is moistened with water.
APPLICATION:
25 kg of Allmax Thin is poured into a container filled with approximately 5.0-6.0 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained.
During the mixing process, no additives should be added that are not specified in the application instructions.
The prepared mortar should be left to mature for 5-10 minutes and then mixed for 1-2 minutes until it becomes homogeneous.
The application thickness is 3-10 mm in a single layer with a plasterer's trowel.
When the plaster has hardened sufficiently, the plaster surface is trifiled and the surface is finished with a damp sponge.
Warnings:
No foreign material (lime, cement, plaster, etc.) should be added to the prepared mortar.
Plastered surfaces should be protected from direct sunlight and harsh weather conditions in the first days, and plastered surfaces should be lightly wetted if necessary.
The applied surface should be protected against rapid drying in windy weather.
It is recommended to apply 2 coats, especially in summer, to prevent the risk of cracking due to rapid drying.
Plaster mesh should be used at joints of different materials and at points where movement is thought to occur.
For the durability of the product, the surface should be watered at regular intervals within 3 days after application.
Do not exceed the specified application surface and instructions for use.
Any coating and painting work to be applied on the plastered surface must be done at least 7 days after the plaster application is complete
Public Works Item No: 04.476/C
Area of Use:
Indoors and outdoors,
On the wall and ceiling,
On exposed concrete surfaces,
It is used on rough plaster and ready-mixed cement based plaster applications.
Features:
It is applied manually.
It is resistant to water, frost and humidity.
It breathes and balances the humidity level by allowing evaporation.
It has a plastic consistency and is easy to apply.
Provides a smooth surface for final coating.
Technical Specifications:
Appearance: Gray Color Powder
Dry Unit Weight: 1400 ± 300 kg/m³
Application Temperature: +5ºC to +35ºC
Water Mixing Ratio: 5.0-6.0 Liters/Bag
Applicable Thickness: 3-10 mm
Drying Time: 24 hours
Compressive Strength: ≥ 6 N/mm²
Bond Strength: ≥ 0.2 N/mm²
Capillary Water Absorption: W0
Water Vapor Permeability Coefficient: µ ≤ 25
Average Thermal Conductivity (W/mK): ≤ 0.93
Fire Response: A1
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
The surface must be cleared of mold oil, dust, paint and adhesion reducing substances.
Before application, cracks and holes should be repaired with appropriate repair mortars.
If necessary, the application surface is moistened with water.
APPLICATION:
25 kg of Allmax Thin is poured into a container filled with approximately 5.0-6.0 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained.
During the mixing process, no additives should be added that are not specified in the application instructions.
The prepared mortar should be left to mature for 5-10 minutes and then mixed for 1-2 minutes until it becomes homogeneous.
The application thickness is 3-10 mm in a single layer with a plasterer's trowel.
When the plaster has hardened sufficiently, the plaster surface is trifiled and the surface is finished with a damp sponge.
Warnings:
No foreign material (lime, cement, plaster, etc.) should be added to the prepared mortar.
Plastered surfaces should be protected from direct sunlight and harsh weather conditions in the first days, and plastered surfaces should be lightly wetted if necessary.
The applied surface should be protected against rapid drying in windy weather.
It is recommended to apply 2 coats, especially in summer, to prevent the risk of cracking due to rapid drying.
Plaster mesh should be used at joints of different materials and at points where movement is thought to occur.
For the durability of the product, the surface should be watered at regular intervals within 3 days after application.
Do not exceed the specified application surface and instructions for use.
Any coating and painting work to be applied on the plastered surface must be done at least 7 days after the plaster application is complete
